Independent DIY Tool Lab Verified Fitment & Sizing Specs Reader-Supported Reviews
FixItRig — DIY Home Repair & Tool Lab

Fiskars Rain Barrel Diverter vs. EarthMinded FlexiFit: Best DIY Rainwater Kit?

Quick Jump: Inside This Guide (8 Sections)

Collecting free rainwater off roof shingles for outdoor garden irrigation sounds effortless—until a heavy summer thunderstorm fills a 55-gallon rain barrel in minutes and dumps hundreds of gallons of excess roof runoff straight over the barrel rim against your concrete foundation. (Note: roof runoff can carry shingle grit, pollen, and bird droppings, so it should only be used for non-potable outdoor watering.) Routing surplus storm water back down the downspout requires a properly leveled overflow diverter matched to your exact downspout profile.

Two DIY diverter kits dominate homeowner builds: the hole-saw EarthMinded FlexiFit Rain Barrel Diverter Kit and the inline pass-through Fiskars DiverterPro Rainwater Kit. FixItRig audited official manufacturer installation manuals and 2″x3″ / 3″x4″ K-style fitment rules for both kits, cross-checked equal-level overflow physics, and synthesized verified homeowner durability feedback—plus we included a full 4-step visual DIY installation blueprint right before the FAQs.

HEAD-TO-HEAD SPEC & FITMENT ANALYSIS • RAINWATER DIVERSIONEDITOR’S PICK: EARTHMINDED (9.5 / 10)
EDITOR’S OVERALL PICK

EarthMinded FlexiFit Rain Barrel Diverter Kit with Hole Saws, Flex Hose, and Winter Cover

EarthMinded FlexiFit

Flexible rubberized FlexiFit diverter cup with bundled 2-1/8″ & 1-1/2″ hole saws, expandable fill hose, and equal-level recirculating overflow.

9.5/ 10 Editorial Score
Downspout Compatibility2″x3″ & 3″x4″ (Narrow Side)
Auto-Overflow RoutingReturns Down Same Pipe
Hole Saws IncludedYes (2-1/8″ & 1-1/2″)
Winter Bypass ModeSnap-On Cover Plate
All Hardware + Saws Included
VS
BEST DEBRIS-FILTER INLINE PICK

Fiskars DiverterPro Inline Rain Barrel Diverter Kit with Hose and Red Winter Plug

Fiskars DiverterPro

Inline cut-pipe rectangular collector featuring a pass-through center chute and winter shutoff plug for straight 2″x3″ or 3″x4″ runs.

8.4/ 10 Editorial Score
Downspout Compatibility2″x3″ or 3″x4″ Cut-In
Auto-Overflow RoutingLevel-Balance / Aux Port
Hole Saws IncludedRequires Pipe Cut + Bit
Winter Bypass ModeRed Rubber Plug Cap
UV-Resistant Resin Housing

Choose EarthMinded FlexiFit If…

  • You do not want to saw your downspout in half: Drills through a single 2-1/8″ circular port using the included hole saw—leaving the vertical downspout structurally intact.
  • You have 2″x3″ or 3″x4″ rectangular spouts: Expands inside standard 2″x3″ drops and oversized 3″x4″ downspouts (when installed on the narrow 3-inch side per EarthMinded’s manual).
  • You want equal-level overflow routing: When leveled with the barrel’s top fill line, excess water is designed to back up and drop down the same downspout rather than spilling over the lid.

Choose Fiskars DiverterPro If…

  • You want an inline screen housing you can inspect: Inline section cut makes it straightforward to check internal leaf buildup if your gutters lack micro-mesh gutter guards.
  • You prefer snipping a pipe section over hole-sawing: Measuring and cutting a clean 4-inch gap lets you slip the inline box straight between upper and lower pipes (check exact 2″x3″ vs. 3″x4″ SKU fitment).
  • You already have Fiskars rain barrel hardware: Matches Fiskars hose barbs and plug ports directly with zero step-down couplings.

Editorial Comparison Summary

■ EarthMinded FlexiFit (9.5)■ Fiskars DiverterPro (8.4)
Equal-Level Overflow Control
9.7 vs 8.5
2″x3″ & 3″x4″ Pipe Fitment
9.6 vs 8.2
Included Tools & Kit Completeness
9.8 vs 8.0
Debris Pass-Through Geometry
9.2 vs 8.8
Winter Freeze Bypass Design
9.4 vs 8.6
Editor’s Overall WinnerEarthMinded FlexiFit (Leads All 5 Evaluation Criteria)
Downspout Cut Needed1x 2-1/8″ Hole
3″x4″ Install RuleNarrow 3″ Side Only
Bundled Saws2-1/8″ & 1-1/2″ Incl.

How We Scored These Diverters: Scores reflect FixItRig’s weighted editorial rubric—Downspout Fitment & Manual Clearances (30%), Overflow & Bypass Design (25%), Included Tools & Hardware Completeness (20%), Debris Pass-Through Geometry (15%), and Verified Homeowner Feedback (10%)—based on manufacturer documentation rather than physical lab testing.

Full Side-by-Side Technical Specification Matrix

Engineering Spec EarthMinded FlexiFit (9.5/10) Fiskars DiverterPro (8.4/10)
Installation Cut Method ✓ Single 2-1/8″ Hole Saw Port (Pipe Stays Whole) Cut & Remove 4″ Section of Vertical Pipe
Fits 2″x3″ & 3″x4″ Spouts? ✓ Yes (Drill Narrow 3″ Side on 3″x4″; Round Needs Adapter) Includes Both 2″x3″ & 3″x4″ Couplers + Dual Barrel Ports
Bundled Hole Saws Included? ✓ Yes (2-1/8″ Metal + 1-1/2″ Barrel Seal Saws) No (Needs Hacksaw / Snips + Barrel Drill Bit)
Overflow Redirect Mechanism ✓ Equalizes & Drops Back Down Exact Same Pipe Pass-Through Weir + Optional Side Hose
Winter Bypass Conversion ✓ Snap-On Color-Match Cover Plate + Screws Red Rubber Side-Port Stopper Plug
Mosquito / Leaf Entry Seal ✓ Closed Flex Hose Into Tight Rubber Grommet Enclosed Tube Into Side Port Seal
Downspout Support Strength ✓ Keeps Continuous Aluminum Column Rigid Splits Upper & Lower Pipe Onto Plastic Collar

Diverter Physics: Why Hole-Saw FlexiFit Beats Cutting Downspouts in Half

Traditional DIY rain barrel kits forced homeowners to unbolt siding straps, hacksaw a 5-inch section cleanly out of painted aluminum downspouts, and wedge a bulky plastic T-box into the gap. That cut-pipe method carries two hidden structural headaches: first, the lower downspout half hangs solely from plastic friction unless re-strapped cleanly into brick masonry; second, mismatched 2″x3″ versus 3″x4″ downspout dimensions leave messy air gaps that splash water down clapboard siding during heavy storms.

EarthMinded FlexiFit eliminates structural cutting altogether by inserting an open flexible elastomer cup through a single 2-1/8-inch circular hole. Rainwater cascading down the inner aluminum walls drops directly into the cup perimeter and flows sideways through a 1-1/4″ corrugated hose into your sealed rain barrel—while center-column roof debris and surplus storm surge plunge effortlessly straight past the cup center down to your ground-level Stealth Flow diffuser or hinged lawn extension!

Spec-by-Spec Breakdown & Manufacturer Manual Rules

CRITERION 1 • AUTO-OVERFLOW & ALIGNMENT

55-Gallon Full-Barrel Backflow & Storm Surge Behavior

✓ Edge: EarthMinded FlexiFit

When a 55-gallon rain barrel reaches capacity during a sustained storm, water inside the horizontal fill hose rises until it matches the downspout collector level. According to EarthMinded’s installation manual, when the downspout hole and barrel inlet seal sit on the exact same horizontal plane, excess water backs into the collector cup and routes straight down the same aluminum downspout—though extreme cloudbursts or leaf-clogged intakes can still cause overflow. Fiskars DiverterPro also bypasses excess center flow once full, though off-level alignment at the inline box collar can seep droplets around the lower aluminum slip joint unless sealed with gutter sealant.

Backflow ControlEqual-Level Alignment
Overflow Lid LeakageLow When Leveled
Collar Drip RiskNone on Hole-Saw Seal
Manual Takeaway: Always keep the fill hose dead level (or sloping slightly downward toward the barrel) so equal-level backflow engages smoothly before water reaches top lid vents.
CRITERION 2 • LEAF & SHINGLE GRIT HANDLING

Autumn Oak Leaf Clump & Asphalt Granule Clog Resistance

✓ Edge: EarthMinded FlexiFit

Internal cup aperture dictates how well a diverter handles roof debris. Fiskars DiverterPro’s ribbed pass-through strainer shelf catches bulky twigs before they enter the side hose—useful for barrel water clarity, yet verified homeowner reviews note that damp oak leaves can bridge horizontally across its plastic weir shelf and slow diversion until cleared. EarthMinded’s wide open center ring lets heavier twigs plunge straight through the hollow downspout column while skimming sheet water off the sidewalls into the barrel.

Shingle Grit DiversionMinimal (Drops Straight)
Weir Leaf BridgingRare on Center Ring
Best Gutter PairType 304 Micro-Mesh
Pro Tip: Pair any rain barrel diverter with DIY Type 304 stainless micro-mesh guards upstairs so mosquitoes, pine needles, and bird droppings stay out of your garden irrigation water.
CRITERION 3 • TOOLS, FITMENT & WINTER SHUTOFF

Bundled Hole Saws, 3″x4″ Side Rule & Winter Bypass

✓ Edge: EarthMinded FlexiFit

Out of the retail box, EarthMinded FlexiFit packs everything needed except your cordless drill and cinder blocks—including BOTH a 2-1/8″ hole saw for the aluminum downspout AND a 1-1/2″ hole saw for drilling the barrel wall grommet. Buying Fiskars DiverterPro separately requires already owning aviation snips/hacksaw blades AND purchasing a separate 1-1/4″–1-1/2″ hole bit for your rain barrel sidewall. For November freezing protection, pulling FlexiFit’s rubber cup out and screwing on its bundled flat cover plate leaves no protruding plastic elbows to crack in winter ice.

FlexiFit CutSingle 2-1/8″ Hole (Bits Incl.)
Fiskars Cut4″ Pipe Gap (BYO Barrel Bit)
Winter Cap SealScrew-On Cover Plate
Sizing Reminder: Check how much rainwater your roof sheds per storm inside our calculator below before choosing a single 55-gallon barrel versus linking two barrels in series.
INTERACTIVE SIZING CALCULATOR

Gutter Size & Downspout Rainfall Capacity Calculator

Enter your roof footprint, pitch, and local peak storm intensity (SMACNA formula) to prevent gutter overflow and foundation washouts.

Adjusted Drainage Area 1,210 sq ft
Peak Storm Runoff 50.3 GPM
Recommended Gutter 5" K-Style
Min. Downspouts Needed 1x (3"x4") or 2x (2"x3")
Sizing Recommendation: For 1,210 adjusted sq ft at 4"/hr peak rain, use 5" K-Style (Std) gutters with 2 oversized 3"x4" downspout(s) (or 3 standard 2"x3" spouts).

SMACNA Formula: Adjusted Area × Rainfall (in/hr) × 0.0104 (runoff coeff. 1.0) = Peak GPM.

Exact Fitment Hardware for This Calculation:
Amerimax 3x4 Oversized Drop Outlet & Adapter Kit Amazon
Raytec Hangtite Hidden Gutter Hangers (25-Pack) Amazon

Calculator Formula & Assumptions (SMACNA): Peak roof runoff is calculated as Adjusted Area = Footprint × SMACNA Pitch Factor (1.00–1.30) and Flow (GPM) = Adjusted Area × Rainfall (in/hr) × 0.623 ÷ 60, assuming an impervious roof runoff coefficient of 1.0. For example, a 1,100 sq ft footprint at a 1.10 pitch factor (1,210 adjusted sq ft) during a 4 in/hr storm produces 50.3 GPM.

Fiskars Rain Barrel Diverter vs EarthMinded FlexiFit Spec Comparison Chart
FixItRig Quick-Reference Comparison: Hole-Saw Install, Auto Overflow & 2×3/3×4 Fitment

Standardized Pros & Cons Breakdown

EarthMinded FlexiFit Advantages

  • Includes both 2-1/8″ and 1-1/2″ hole saws—saving $25+ in extra hardware store bit trips
  • Leaves vertical aluminum downspout structural walls intact without cutting pipe in half
  • Self-balancing automatic overflow returns excess rainwater harmlessly down the exact same spout
  • Includes a neat screw-on winter cover plate so your barrel stays completely dry during freezing months

Fiskars & Diverter Tradeoffs

  • Fiskars requires cutting a 4-inch gap completely out of existing metal downspouts
  • Neither diverter filters microscopic roof asphalt algae—stick strictly to garden & lawn watering (non-potable)
  • On steep 8/12+ roofs during cloudbursts, fast central water velocity fills barrels slower on wide 3″x4″ drops unless matched carefully

Final Showdown Verdict: Which Rainwater Kit Belongs on Your House?

OVERALL BEST PICK (9.5 / 10)

EarthMinded FlexiFit Kit

EarthMinded FlexiFit Diverter Kit

Best complete DIY rainwater kit—includes hole saws, fits 2″x3″ & 3″x4″ spouts (narrow side), and routes excess water back down the spout when leveled.

INLINE SCREEN PICK (8.4 / 10)

Fiskars DiverterPro Kit

Fiskars DiverterPro Kit

Solid inline alternative for homeowners who prefer snipping an inspection box directly into straight 2×3 downspouts.

How to Install a Rain Barrel Diverter Yourself (4-Step Visual DIY Guide)

Whether you choose EarthMinded FlexiFit or another hole-saw diverter, proper elevation and level alignment determine whether your barrel fills cleanly to 55 gallons or leaks prematurely down brick siding. Follow this four-step installation protocol:

4-Step Visual DIY Guide showing cinder block leveling, 2-1/8 inch hole saw drilling, FlexiFit cup insertion, and winter bypass overflow
FixItRig 4-Step Visual Blueprint: Leveling Cinder Blocks, Hole-Saw Drilling & Automatic Overflow Alignment
  1. Step 1 — Elevate Your Barrel on Solid Cinder Blocks & Mark the Exact Level Line: Never set a 55-gallon rain barrel flat on soft dirt—a full barrel weighs roughly 460 pounds and sinks sideways, and you need gravity head height below the bottom spigot to fill a 5-gallon watering can or garden hose! Stack two solid concrete blocks flat on compacted gravel paver sand right beside your downspout. Set the barrel in place, hold a 24-inch carpenter’s level horizontally from the top fill port line of your barrel over onto the downspout face, and mark the drill center dead level (or 1 inch higher on the downspout than the barrel port).
  2. Step 2 — Drill Cleanly With the 2-1/8″ & 1-1/2″ Hole Saws: Chuck the bundled 2-1/8″ bi-metal hole saw into your cordless drill (high-speed clutch setting), align the pilot bit onto your center mark on the flat downspout face, and drill slowly with light pressure so thin aluminum edges cut cleanly without grabbing. Repeat with the 1-1/2″ hole saw on the upper flat wall of your plastic rain barrel and deburr any sharp plastic shavings with a utility knife.
  3. Step 3 — Pinch & Snap the FlexiFit Cup Facing Upward + Seal the Grommet: Push the black rubber barrel seal tightly into the 1-1/2″ barrel port. Pinch the white flexible FlexiFit diverter cup folds inward like a taco, push it cleanly into the 2-1/8″ downspout hole until its outer collar flange seats flush against aluminum, and verify the recessed water-catching scoop faces UPWARD toward the roof gutter! Stretch the ribbed white fill hose snugly onto both barbs.
  4. Step 4 — Test Overflow Balance & Prep Winter Bypass Cap: Run a garden hose down the upper gutter for three minutes until the barrel reaches max fill line—confirm water stops rising and smoothly cascades down the center downspout hole toward your yard drainage outlet. Before your first hard November freeze, drain the barrel completely, pull out the FlexiFit cup, and screw on the included flat winter bypass plate so ice never splits your plastic barrel!

Essential Rain Barrel Diverter & Setup Hardware Kit

EarthMinded FlexiFit Rain Barrel Diverter & Parts Kit (Hole Saws Included)
Fits 2″x3″ and 3″x4″ rectangular downspouts (drill narrow 3″ side on 3×4) with bundled 2-1/8″ & 1-1/2″ hole saws, stretch hose, rubber seal, and winter cover plate.

Check on Amazon

Fiskars DiverterPro Inline Rain Barrel Diverter Kit
Cut-pipe inline collector with built-in leaf strainer shelf, flexible fill hose, and winter shutoff plug for 2″x3″ downspouts.

Check on Amazon

24-Inch Torpedo / Box Level & Cordless Drill Driver Combo
Ensures the diverter hole and barrel seal align dead level so hydrostatic backflow stops barrel overflow every storm.

Check on Amazon

Raptor Type 304 Stainless Micro-Mesh Gutter Guards (Upstream Debris Filter)
Stops pine needles, oak pollen, and squirrel debris upstairs before rainwater ever reaches your diverter fill hose.

Check on Amazon

Frequently Asked Questions

Will EarthMinded FlexiFit fit a 3″x4″ or round downspout?

Yes for 3″x4″ rectangular downspouts—with one critical manual rule: on a 3″x4″ downspout, EarthMinded requires drilling the 2-1/8″ hole on the narrow 3-inch side (not the wide 4-inch face) so the internal diverter cup spans the pipe properly. For round downspouts, check your exact pipe diameter first; standard FlexiFit kits target rectangular 2″x3″ and 3″x4″ spouts, while round pipes typically require a dedicated round-downspout diverter or adapter kit.

Why is my rain barrel still overflowing out the top lid even with a diverter installed?

The most common cause of overflow leaks is drilling the diverter hole in the downspout higher than the barrel’s top overflow return level, or letting the fill hose sag down into a U-belly dip. Always align the downspout hole level with the upper barrel entry grommet so equal-level back-pressure can redirect excess water down the downspout once the barrel fills.

How fast does a 55-gallon rain barrel fill during a normal rainstorm?

Every 1,000 square feet of roof collects roughly 623 gallons per 1 inch of rain! Even if one downspout serves just 400 square feet of porch roof, a light 0.25-inch afternoon shower delivers over 60 gallons—topping off a 55-gallon barrel in under 20 minutes. Verify your roof’s storm output inside our Gutter Rainfall Capacity Calculator.

Can I link two 55-gallon rain barrels together using one EarthMinded diverter?

Yes! EarthMinded also sells a simple barrel-to-barrel linking hose kit (using the exact same 1-1/2″ hole saw included in your main kit) connecting the bottom or upper side ports of Barrel A into Barrel B—doubling storage capacity to 110 gallons before triggering downspout bypass.

Should I install a rain barrel diverter on a downspout connected to a Stealth Flow or Zip Hinge?

Absolutely—and installing a hole-saw diverter like FlexiFit 34 inches up the vertical pipe leaves your lower Zip Hinge flip-up extension or Amerimax Stealth Flow chute completely intact to carry surplus winter & storm water safely away from foundation footings.

Do rain barrels attract mosquitoes inside the diverter fill hose?

Sealed diverter setups (unlike open-top screened barrels sitting directly under sawed-off elbows) block adult mosquitoes from flying into standing water—provided you keep the barrel’s top inspection lid gasketed tight and drop one natural Bti mosquito dunk inside every 30 days during summer.

Is roof rainwater safe for vegetable gardens if I have asphalt shingles?

University extension tests show trace metals from aged asphalt shingles sit well below irrigation concern levels for ornamental flowers, turf, and trees; however, many cautious gardeners route roof runoff onto ornamentals, shrubs, and compost piles while keeping raised edible lettuce beds on municipal hose water (and never drinking untreated roof water).

FixItRig Editorial & Engineering Research Staff
FixItRig Editorial & Engineering Research Staff US Residential Exterior & Drainage Research
SMACNA Drainage Specs Verified Manufacturer Specs IRC & OSHA Compliance

Every gutter guard, telescoping wand, and drainage fitting covered by the FixItRig Editorial & Engineering Research Staff is audited against official manufacturer specifications, verified long-term homeowner feedback, and SMACNA, IRC, and OSHA residential building codes. Before publishing or updating any guide, our US editorial team cross-checks thread diameters, material gauges, and outlet fitment so homeowners buy the right hardware the first time.

Affiliate Disclosure: As an Amazon Associate, FixItRig earns from qualifying purchases made through links on this page at no additional cost to you.